| Sorry it has taken soooo long. This is a partial list of the Model "A" parts that I have worked on for a loooong time. These are the bigger body parts, and rear ends, front ends, and motors. I have an entire wall of smaller parts that are going to get sand blasted A.S.A.P., and painted with primer (or oiled according to necessity) to preserve them, and I will post the list of those parts also.
I will be selling all the parts that I would not need for building a project car of my own, BUT if the price is right I would consider selling the whole load with the 31' body with a title included. I will make a more detailed description of the body at the end of the list. If you would like a look at some of the parts I can scan pictures and attach them to e-mail if anyone is interested.
#1. Body parts section ...
ItemQuantity One 1931 two door sedan body in good condition complete with
doors. gas tanks 28'-29' 3
gas tanks 30'-31' 2
(there are additional gas tanks that are attached to firewalls and are listed elsewhere) firewall w/windshield frame 1
hood good condition 2
hood great condition (goes with the body) 1
sun visor 2
drivers door 28'-29' (fair condition) 2
drivers door 30'-31'1
passenger door 30'-31'2
rear section of a sedan body (rusted at bottom) 1
Coupe left rear window section (glass broken) 1
Coupe running boards w/rocker attached set1
left rocker 1
running boards set w/rubber (goes with body)1
running boards set w/diamond pattern1
rocker panel set sedan (goes with body) 1
body top piece above drivers door 1
left front fenders 28'-29' (very fixable) 2
left front fender w/spare tire pocket 30'-31' 1
set of front fenders 30'-31'1
set of rear fenders sedan 30'-31' 1
set of rear fenders coupe 28'-29' 1
sedan rear left fender 30'-31'1
front bumper 30'-31' (needs rechromed)1
front bumper 28'-29' (needs rechromed)1
body window frame w/o window insert 2
body window frame w/gas tank attached 28'-29' 1
(has side body panel and fire wall attached)
body window frame w/o gas tank attached 28'-29' 1(has side body panel and fire wall attached)
window frame insert w/o window (goes with body) 1
firewall only 1
rear bumper set 28'-29' (need rechromed)2
rear bumper set 30'-31' (need rechromed)5
bumper support set3
misc. bumper supports 6
steering column w/wheel (good cond. rubber ok)1
steering column w/wheel (fair cond. rubber cracked) 4
steering column w/o wheel 3
steering rod with worm gear only2
front under body support1
light switch rod (fair cond.) 1
steering column sleeve w/bracket support1
Coupe seat frame all intact no upholstery 1
head light sets 5
head light bars 4
oil pan deflector 2
radiator shell 28'-29' (sad shape)3
radiator shell 30'-31' (sad shape)1
wood body pieces for firewall and floor 3 #2. under body section front end spring sets 6
rear end spring sets8
front ends9
rear ends 12 some of these have drums still on them and some don't (but there is a HUGE stack of drums, not to mention brake parts,for both front and rear ends). Most of the rear ends have radius rods attached (7). There are some assorted axles, bearings, and housings for the rear ends. Model "A" frames3
rear crossmember section2
center section1
Model "T" frame w/fender supports 1 #3. motor and transmission parts complete motor from head to oil pan 3
one motor disassembled enough parts to make whole 1
intake manifold 3
exhaust manifold2
exhaust manifold (WITH HEATER BLOWER ATTACHMENT)1
motor bellhousing (between motor and3
tranny bellhousing)
transmission w/bellhousing and shifter attached 3
bellhousing for tranny2
shifter 3
cranks6
radiator 28'-29'5
radiator 30'-31'2
flywheel9 #4. small truck parts truck bed (3 sides no bottom rails for the wood)1
truck tail gait 1
truck cap w/rear window hole all one piece1 this looks like this was the beginning of a truck project. #5. 1 1/2 ton Model "A" truck parts 1 1/2 ton front axle1
1 1/2 ton frame 1
1 1/2 ton rear end w/rims 1
(a bit rusty but they're intact)
this is it for now ... I'm tired of picking parts! I will be on to the remainder of the smaller parts soon. And I will be cleaning and blasting soon if no one makes an offer on the lot as is.
As to the body it has a few bullet holes that are very repairable. It has only one very small area that is in need of any rust repair. Structurally I have seen very good restorations made from bodies that have had rust 6 inches from the bottom up ... BUT THIS BODY DOES NOT HAVE RUST LIKE THAT! Just a small section toward the rear passenger side that isn't even worth mentioning. Other than the usual surface rust from being stored for a long time it's in very good shape. The rear body panel was removed below the rear window (to make a delivery truck project I would suppose) but it is intact and could be mig welded back in easily. If you are intersted in the parts or anything else drop me a line. If you know any other possible intersted parties please pass this list along. Brian Brackney
Springfield, Ohio brianb56@erinet.com address and phone number on request
| 
E-Mail Comment to Webmaster